80 Ton Mechanical Punch Press Machine

Punching capacity: 80 ton
Punch press machine price: 7,500 USD FOB China

The 80 ton mechanical punch press machine is the first size in our range that behaves like a production press rather than a workshop press: 120 mm stroke, 45 strokes per minute, a 780 × 470 mm bolster and a 5.5 kW motor, on a 3,700 kg frame. It punches 6 mm mild steel with a 74 × 74 mm square hole and runs progressive dies without complaint. The price is 7,500 USD FOB China in standard configuration.

This page covers the capacity, the full specification, the difference between the 80 ton mechanical and hydraulic versions, the parts that wear, the guarding we recommend for a press of this size, and what the 7,500 USD actually includes.

80 ton mechanical punch press machine
The 80 ton mechanical press: 120 mm stroke, 45 SPM, 780 × 470 mm bolster.

● 1. What an 80 ton punch press can punch

At 80 tons nominal, and planning at 80 percent (628 kN), the press cuts 6 mm mild steel with 299 mm of perimeter — a 74 × 74 mm square hole — or 4 mm steel with 448 mm of perimeter, which is a 112 × 112 mm square. That is the class where electrical cabinets, cable trays, truck brackets and agricultural parts are made.

Capacity by material thickness

Force (kN) = perimeter (mm) × thickness (mm) × shear strength (N/mm²) ÷ 1000. Mild steel ≈ 350 N/mm², stainless ≈ 500 N/mm², aluminium ≈ 200 N/mm². Nominal 80 ton = 785 kN; we plan at 628 kN.

Material thicknessMax cutting perimeter at 80 t (80% rule)Typical shape it allows
2.0 mm897 mmLarge cut-outs, cabinet doors, panels
3.0 mm598 mm150 × 150 mm square, or Ø190 mm round
4.0 mm448 mm112 × 112 mm square, or Ø142 mm round
5.0 mm359 mm90 × 90 mm square
6.0 mm299 mm74 × 74 mm square, or Ø95 mm round
8.0 mm224 mm56 × 56 mm square
10.0 mm179 mm44 × 44 mm square — near the limit

Stainless steel and high-tensile steel are the exception: divide the perimeter by about 1.4, because the shear strength is close to 500 N/mm² instead of 350. If most of your work is stainless, tell us at quotation stage; we set the die clearances differently and we may recommend the 100 ton model.

● 2. Specification of the 80 ton mechanical punch press

Technical data of the 80 ton model

These are the numbers of the standard machine. Stroke, SPM and die height can be modified, but the four figures that decide whether your die fits are force, stroke, bolster and die height — check them against your tooling drawing before you order.

ParameterValue
Nominal force80 ton
Nominal stroke120 mm
SPM (strokes per minute)45
Die height adjustment45 mm
Between slide centre and frame (throat)270 mm
Bolster (table)780 × 470 mm
Blanking hole diameter180 mm
Main motor5.5 kW
Outline dimension1,600 × 1,200 × 2,650 mm
Net weight3,700 kg

The 120 mm stroke is the reason this model is popular for forming as well as punching. A longer stroke gives room for a taller die, for drawing and for parts that need to be lifted clear of the tool. The 45 SPM is a mechanical compromise: at this tonnage, speed and flywheel energy trade against each other, and 45 strokes per minute is the setting that keeps the flywheel recovering between strokes on a 5.5 kW motor.

● 3. Mechanical or hydraulic at 80 tons?

Buy mechanical if your work is punching and blanking at a fixed stroke and you want speed and the lowest cost per part. Buy hydraulic if you need full tonnage anywhere in the stroke, pressure dwell for forming, or adjustable force to protect an expensive die.

Criterion80 t mechanical80 t hydraulic
Force in the strokePeaks at bottom dead centreFull 80 t at any point
Speed45 SPMLower, typically 10–25 SPM
Forming and drawingLimited to shallow workBest choice, pressure dwell available
Die protectionNeeds overload release and brake monitorPressure relief protects the tool
Price7,500 USDHigher, and maintenance is oil and seals
Best forPunching, blanking, louvering, high volumeDeep forming, thick plate, variable jobs

For a workshop that does both, the usual answer is an 80 ton mechanical press for punching plus a smaller hydraulic press for forming, rather than one hydraulic machine trying to be fast at both.

● 4. Punch press machine parts and what wears

The 80 ton press has the same architecture as every mechanical C-frame press — motor, flywheel, clutch, brake, crankshaft, connecting rod, slide, guides, bolster, frame — but at this tonnage the parts are heavy enough that maintenance stops being optional.

mechanical punch press machine parts
  • Clutch and brake: the safety pair. Adjust together, measure stopping angle.
  • Connecting rod: big-end bearing takes the full tonnage. Grease weekly.
  • Crankshaft: scored only by a dry bearing or an overload.
  • Slide guides: set the die alignment. Check clearance yearly.
  • Flywheel bearings: noise and heat are the first signs.
  • Overload release: must be re-set correctly after every trip.

On an 80 ton press the overload protection is not a luxury. A single jammed slug can generate more than twice the nominal tonnage in a fraction of a second, and the hydraulic overload device in the slide is what saves the crankshaft. Test it once a year, and never block it to "make the press stronger".

● 5. Applications: where this size earns its price

The 80 ton class is the workhorse of metal fabrication: electrical enclosures and junction boxes, cable tray and strut profiles, HVAC brackets, truck and trailer parts, agricultural implements, shelving and racking components, and progressive-die work on 2–4 mm sheet.

products of mechanical punch press machine
Parts produced on the 80 ton press: brackets, covers, plates and progressive-die blanks.

With a progressive die and a coil feeder the same press becomes a small automatic line: coil, straightener, feeder, press, scrap cutter. We can quote the complete line, and we set the feeder stroke and the die height together so the installation works on the first day rather than after three service visits.

● 6. Price: what the 7,500 USD includes

7,500 USD is the FOB China price of the 80 ton machine in standard configuration. It is the sixth line of our published punch press machine price list, and it is the same number we put in the quotation.

Included: complete 80 ton press, 5.5 kW motor wired for your voltage, mechanical clutch and brake, hydraulic overload protection in the slide, foot switch, two-hand control, fixed front guard, manual in English, exploded drawing, factory test run, export packing.

Not included: dies, light curtain or interlocked enclosure, coil feeder and straightener, automatic lubrication, special stroke or SPM, sea freight, insurance, duties, inland transport.

Cost breakdown of an 80 ton project

Cost lineTypical shareComment
Press55–70%7,500 USD for the standard 80 ton model
Die or progressive tool15–35%A progressive die can cost as much as the press
Feeder and automation5–15%Coil feeder, straightener, scrap cutter
Freight and duties5–12%3,700 kg needs a 20-foot container minimum

When you compare two quotes for an 80 ton press, compare the frame weight. A lighter frame at the same nominal tonnage deflects more under load, and the die pays for it with short punch life. 3,700 kg for 80 tons is a solid, conventional figure for a stress-relieved C-frame.

● 7. Guarding and safety on an 80 ton press

At this tonnage the guard is not a fence, it is a safety system. We recommend a light curtain with a brake monitor, plus a fixed rear guard and an interlocked side door for die changes.

  • Light curtain: protects the point of operation and allows fast loading by hand. Must be combined with a brake monitor, because the curtain is only as good as the stopping time it assumes.
  • Two-hand control: both buttons within 0.5 s, so both hands are outside the die when the stroke starts.
  • Interlocked die-change door: the press cannot cycle with the door open; the flywheel must be stopped before access.
  • Lock-out during maintenance: main switch off and locked, flywheel at rest. A mechanical press stores energy in the flywheel even with the motor off.

We can supply the machine with the guarding package installed and tested, or ship the guarding as a kit with a wiring diagram if you prefer to install locally.

● 8. Installation and maintenance

Installation requirements

The 80 ton press needs a level concrete floor, a 380 V three-phase supply and about 1.6 × 1.2 m of floor space plus clearance for the material. No special foundation is required, but we recommend anti-vibration pads and a floor that can carry 3,700 kg plus the die and the material.

Maintenance schedule

FrequencyTask
Every shiftOil level, air pressure, guard and light curtain test, unusual noise, foot switch cable
WeeklyGrease connecting rod and crankshaft bearings, check clutch and brake adjustment, tighten bolster and die clamps
MonthlySlide guide clearance, flywheel bearing temperature, electrical terminals, overload device check
YearlyMeasure brake stopping time, change oil, inspect frame bolts, test the hydraulic overload with a gauge

● 9. Our factory

FYCHIS has manufactured mechanical presses in Chongqing since 2004, from 10 to 100 tons, together with the dies, feeders and guarding that go with them. We test every press with a die before packing and we ship to more than 40 countries.

punch press machine in production
mechanical punch press machine for sale

If you want to see the machine under power before you pay, we record a video test with your die or with a sample die of the same tonnage, and third-party inspection at our factory is welcome.

Other names buyers use

This model is also sold as a mechanical punch press machine for sale, a punch press machine for steel, a punch power press machine or a punch press stamping machine, and the pneumatic clutch version is often quoted as an 80 ton pneumatic punch press machine. All of them describe the same 120 mm stroke, 45 SPM press. Ask for the clutch type in writing, because that is where two quotes for the same 80 ton machine usually differ.

Still comparing sizes? The punch press machine buying guide puts the whole range from 10 to 200 tons side by side, with the tonnage table, the mechanical versus hydraulic comparison and the HS codes for import.

Factory, wholesale and buying guide

As a punch press machine manufacturer and supplier in China we sell wholesale to distributors and directly to factories, and every machine is quoted from our own factory price list. If you are unsure how to select punch press machine tonnage, send the part drawing and we run the calculation with you before you commit. We also build the pneumatic punch press machine range and the hydraulic presses, and we can supply a used punch press machine rebuilt and tested in our workshop when a new machine is out of budget. For safe operations, the manual and the guarding checklist are written for the operator, not for the engineer.

● 10. Frequently asked questions

What is the price of an 80 ton mechanical punch press machine?

7,500 USD FOB China in standard configuration. Dies, feeders, guarding upgrades, special voltage, freight and duties are quoted separately.

How thick can an 80 ton press punch?

6 mm mild steel with a 299 mm perimeter (74 × 74 mm square), 8 mm with 224 mm, and 10 mm only with small holes. Reduce the perimeter by about 30 percent for stainless steel.

What is the difference between the 80 ton and the 100 ton model?

20 tons of force, a bigger bolster and a 7.5 kW motor on the 100 ton, for 1,500 USD more. If your work is mostly 6 mm or you plan to run progressive dies with several stations, the 100 ton is the better long-term buy.

Can the 80 ton press run a progressive die with a coil feeder?

Yes. The 120 mm stroke and the 780 × 470 mm bolster have room for a multi-station die, and we quote the feeder, straightener and scrap cutter with the press so the line is set up together.

What motor power and voltage does it use?

5.5 kW, 380 V three-phase 50 Hz as standard; 220 V, 415 V, 440 V and 60 Hz are available on request.

What is the HS code?

8462.49 for a non-NC punching machine, 8462.41 if numerically controlled, 8207.30 for the dies.

How is it shipped?

In an export wooden case with the slide blocked and the flywheel locked. 3,700 kg fits a 20-foot container with the die and the accessories; we confirm the loading plan before booking.

What warranty do you give?

12 months on mechanical parts, excluding wearing parts. Spare parts ship from stock against the part numbers in the exploded drawing.

● Recommended Models